Huawei RRU User Manual Download Page 25 | Manualshive

Page: 25 / 100

background image

Acid

CAUTION

If the acid overflows, it should be absorbed and neutralized immediately.

When handling a leaky battery, protect against the possible damage caused by the acid. Use the
following materials to absorb and neutralize acid spills:

l

Sodium bicarbonate (baking soda): NaHCO

3

l

Sodium carbonate (soda): Na

2

CO

3

Antacids must be used according to the instructions provided by the battery manufacturer.

Lithium Battery

CAUTION

There is danger of explosion if the battery is incorrectly replaced.

l

Replace the lithium battery with the same or equivalent type recommended by the
manufacturer.

l

Dispose of the used battery according to the instructions provided by the manufacturer.

l

Do not dispose of the lithium battery in fire.

1.5 Radiation

Electromagnetic Field Exposure

CAUTION

High power radio-frequency signals are harmful to human body.

Before installing or maintaining an antenna on a steel tower or mast with a large number of
transmitter antennas, the operator should coordinate with all parties to ensure that the transmitter
antennas are shut down.

The base transceiver station (BTS) has RF radiation (radiation hazard). Suggestions for the
installation and operation of BTSs are given in the following section. Operators are also required
to comply with the related local regulations on erecting BTSs.

l

The antenna should be located in an area that is inaccessible to the public where the RF
radiation exceeds the stipulated value.

RRU
User Guide

1 Safety Information

Issue 01 (2008-04-18)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd

1-7

«
...
23
24
25
26
27
...
»

Summary of Contents for RRU





































































































Reviews:

No comments

Related manuals for RRU

Brand: Xenith Pages: 17

Brand: Barco Pages: 25

Brand: Barco Pages: 16

Brand: Harken Hoister Pages: 12

Resusci Baby QCPR

Brand: laerdal Pages: 8

Brand: Navibe Pages: 8

Brand: Empire Comfort Systems Pages: 4

Brand: Baumer Pages: 3

Brand: EEZ RV Pages: 31

Brand: Trius Pages: 8

Brecknell SBI-100

Brand: AGRI TRONIX Pages: 34

Brand: WABCO Pages: 48

Brand: Soluna Pages: 52

Brand: Linear Pages: 3

Brand: VIKING BAGS Pages: 2

Brand: Silver Cross Pages: 20

Brand: Fab Fours Pages: 19

Brand: METRON Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands