Huawei RRU User Manual Download Page 15

Page: 15 / 100

About This Document

Purpose

This document describes the RRU hardware and provides instructions in hardware installation,
cable connections, hardware installation check, and hardware maintenance. This document is
applicable to RRU3804 and RRU3801E.

Product Versions

The following table lists the product versions related to this document.

Product Name

Product Version

RRU

V100R009

V100R010

V200R001

Intended Audience

This document is intended for:

NodeB installers

System engineers

Site maintenance engineers

Change History

For changes in the document, refer to

Changes in RRU User Guide

Organization

1 Safety Information

2 RRU and SRXU Hardware

This describes the RRU equipment, SRXU equipment, and related cables.

3 Installing RRU and SRXU Hardware

RRU
User Guide

About This Document

Issue 01 (2008-04-18)

Huawei Proprietary and Confidential

Summary of Contents for RRU





































































































Search results

Summary of Contents for RRU

Reviews:

Related manuals for RRU

Brands by name

Popular brands

Huawei RRU, User Manual

Search results

Summary of Contents for RRU

Reviews:

Related manuals for RRU

Brands by name

Popular brands