Huawei Mediapad S7-PRO Maintenance Manual Download

Page: 26 / 97

S7-PRO Maintenance Manual (Basic Version V2.1)

INTERNAL

2012-07-20

Huawei Proprietary and Confidential

Page 26 of 97

Step 2

If the message "Phone is not in download mode" is displayed, you may not uncheck

Program

Boot Loaders

(mandatory for upgrade in the trusted mode). Then uncheck

Program Boot

Loaders

as shown in the following figure.

Click

Scan&&Download

, if the message "port open" is displayed, check whether the driver

is properly installed, and whether

DBAdapter Reserved Interface

port functions well.

5.4 Viewing the Software Version

In the standby state, choose

Settings

About phone

to view the information about the

software version.

6 Maintenance Tools

Name: constant-temperature hot air gun

Purpose: heat components

Summary of Contents for Mediapad S7-PRO


































































































Search results

Summary of Contents for Mediapad S7-PRO

Reviews:

Related manuals for Mediapad S7-PRO

Brands by name

Popular brands

Huawei Mediapad S7-PRO, Maintenance Manual

Search results

Summary of Contents for Mediapad S7-PRO

Reviews:

Related manuals for Mediapad S7-PRO

Brands by name

Popular brands