Huawei Mediapad S7-PRO Maintenance Manual Download | Manualshive

Page: 16 / 97

background image

S7-PRO Maintenance Manual (Basic Version V2.1)

INTERNAL

2012-07-20

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

Page 16 of 97

5.3 Upgrade Using the USB

5.3.1 Entering the USB Upgrade Mode

When the system is powered on, quickly press the

VOLUME_UP

button and the

VOLUME_DOWN

button. If it is the first time for your PC to connect the USB, the message

"Found New Hardware" will be displayed, which indicates that the system has entered the
USB upgrade mode successfully, as shown in the following figure.

5.3.2 Installing the USB Device Driver

If the driver has not been installed before, you must install the driver on the PC before the
update using the USB.

Step 1

When the MediaPad is connected, it enters into the Emergency Download mode, and a
window is displayed, showing the port Qualcomm HS-USB QDLoader 9008. If the port
driver has not been installed before, a message for installing the driver will be displayed.

«
...
14
15
16
17
18
...
»

Summary of Contents for Mediapad S7-PRO


































































































Reviews:

No comments

Related manuals for Mediapad S7-PRO

Brand: Zoostorm Pages: 22

Brand: Xplore Pages: 16

Brand: Bamboo Pages: 18

Pro-Ject Debut SE II

Brand: Pro-Ject Audio Systems Pages: 7

Brand: Gadhouse Pages: 28

Brand: Hitachi Pages: 26

Brand: promethean Pages: 8

Brand: jp.ik Pages: 2

Brand: boytone Pages: 14

Brand: Motion Pages: 7

Brand: Krüger & Matz Pages: 40

Brand: Krüger & Matz Pages: 44

Brand: Krüger & Matz Pages: 44

Brand: Krüger & Matz Pages: 76

Brand: Studebaker Pages: 20

ZiGnature Pad 1410

Brand: 10ZiG Technology Limited Pages: 42

Brand: auna Pages: 24

Brand: Technaxx Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands