Huawei LampSite Installation Manual Download Page 9

Page: 9 / 100

Installation Preparations

About This Chapter

Before starting the installation, you must obtain the required reference documents, tools, and
instruments, and familiarize yourself with the skills required.

2.1 Reference Documents

Before the installation, you must read the following documents:

2.2 Preparing Tools and Instruments

This section describes the tools and instruments that must be prepared before the installation.

2.3 Requirements for Installation Personnel

This section describes requirements for installation engineers. They must be qualified and
trained, and familiar with correct operation methods and safety precautions before performing
any operations.

LampSite
Installation Guide

2 Installation Preparations

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Summary of Contents for LampSite





































































































Search results

Summary of Contents for LampSite

Reviews:

Brands by name

Popular brands

Huawei LampSite, Installation Manual

Search results

Summary of Contents for LampSite

Reviews:

Brands by name

Popular brands