Huawei LampSite Installation Manual Download Page 51

Page: 51 / 100

5.1 Information About the Installation

This section describes the information that you must be familiar with before installing a pRRU,
including the pRRU product family, installation scenarios, installation space and environment
requirements.

5.1.1 pRRU Product Family

This chapter describes the configurations and functions of the pRRU components.

Table 5-1

lists the pRRU product family.

Table 5-1

pRRU product family

Categor
y

Equipment

Optional
Item

Quantity

Function

Main
equipmen
t

pRRU

Mandatory

Processes the radio frequency
signals.

External
antenna

Optional

Provides external antennas for
the pRRU.

NOTE

Configure two external antennas
for each RF daughter board.

AC/DC power
adapter

Optional

Provides power supply for the
pRRU and includes power
cables and installation kits.

Auxiliary
device

Mounting kits

Mandatory

Supports the pRRU
installation on a wall, pole,
ceiling, or keel. The mounting
kits vary with the pRRU
installation mode.

Extender

Optional

Extends the distance between
the pRRU and RHUB.

5.1.2 pRRU Installation Scenario

The pRRU can be installed on a wall, ceiling, pole, or keel. The following table describes the
installation in different scenarios.

LampSite
Installation Guide

5 Installing a pRRU

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Summary of Contents for LampSite





































































































Search results

Summary of Contents for LampSite

Reviews:

Brands by name

Popular brands

Huawei LampSite, Installation Manual

Search results

Summary of Contents for LampSite

Reviews:

Brands by name

Popular brands