Huawei LampSite Installation Manual Download

Page: 61 / 100

NOTE

The pRRU cannot be grounded. If the pRRU is grounded but the RHUB connected to this pRRU is
not, the pRRU may fail to be powered on.

A minimum distance of 50 cm must be reserved between the pRRU and the incandescent lamp.

The installation spacing between the pRRU and the temperature sensor must be greater than 50 cm.

It is good practice to install the pRRU on materials that can tolerate a temperature higher than 65°C
and have an ignition point higher than 70°C.

5.4.1 pRRU Installation Kits

This section describes the pRRU installation kits.

Figure 5-6

shows the exterior of the pRRU installation kits.

Figure 5-6

pRRU installation kits

(1) V clamp

(2) Plate

(3) Screw (M6x50)

(4) Plastic expansion sleeve

(5) Bolt (M6x80)

(6) Flat washer

The following figure shows the specifications of the installation plate.

LampSite
Installation Guide

5 Installing a pRRU

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Summary of Contents for LampSite





































































































Search results

Summary of Contents for LampSite

Reviews:

Related manuals for LampSite

Brands by name

Popular brands

Huawei LampSite, Installation Manual

Search results

Summary of Contents for LampSite

Reviews:

Related manuals for LampSite

Brands by name

Popular brands