Huawei LampSite Page 85 Installation Manual Download | Manualshive

Page: 85 / 100

background image

NOTE

l

The Extender can be used to lengthen the distance between the RHUB and the pRRU connected using
the Ethernet cable. If the Extender is used, the Ethernet cable is divided into two parts, one between
the RHUB and the Extender and the other between the Extender and the pRRU.

l

When two Ethernet cables are used to transmit CPRI signals, connect one end of the cables to the
CPRI_E0 and CPRI_E1 ports on the pRRU panel and the other end to any two ports of CPRI_E0 to
CPRI_E7 on the RHUB panel. This document describes signal transmission using one Ethernet cable
as an example.

Figure 5-35

shows the cable connection when the pRRU is configured with two RF Daughter

Boards.

Figure 5-35

pRRU cable connection (2)

(1) Ethernet cable

(2) RF jumper

(3) AC/DC power adapter

(4) Power cable of the AC/DC power adapter

NOTE

l

The Extender can be used to lengthen the distance between the RHUB and the pRRU connected using
the Ethernet cable. If the Extender is used, the Ethernet cable is divided into two parts, one between
the RHUB and the Extender and the other between the Extender and the pRRU.

l

When two Ethernet cables are used to transmit CPRI signals, connect one end of the cables to the
CPRI_E0 and CPRI_E1 ports on the pRRU panel and the other end to any two ports of CPRI_E0 to
CPRI_E7 on the RHUB panel. This document describes signal transmission using one Ethernet cable
as an example.

5.7.4 Cable Connections (LTE TDD)

This section describes the cable connections for a single pRRU and multiple pRRUs.

Before installing the pRRU cables, you must be aware of the following information:

l

The pRRU can obtain power supply through the power over Ethernet (PoE) or AC/DC
power adapter. You are suggested to use AC/DC power adapter.

l

For external antennas corresponding to RF daughter board 1, the TX port and RX port are
ANT0 and ANT1, respectively. For external antennas corresponding to RF daughter board

LampSite
Installation Guide

5 Installing a pRRU

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

80

«
...
83
84
85
86
87
...
»

Summary of Contents for LampSite





































































































Reviews:

No comments

Related manuals for LampSite

Brand: NORLUX Pages: 2

Brand: Taylor Pages: 70

Brand: Raith Pages: 26

Brand: Kane Pages: 16

Brand: Bard Pages: 36

Brand: Bard Pages: 2

Brand: Bard Pages: 30

Brand: Bard Peripheral Vascular Pages: 44

Crouse-hinds series

Brand: Eaton Pages: 32

COOPER POWER SERIES

Brand: Eaton Pages: 8

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

Brand: Marani Pages: 35

Aesculap S4 Cervical

Brand: B. Braun Pages: 43

Dynamique Biski

Brand: Enabling Technologies Pages: 44

Brand: Reflex Marine Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands