Huawei IPC6221-VRZ-SP Configuration Manual Download Page 51

Page: 51 / 126

Parameter

Description

Brightness

Indicates an attribute of visual perception in which a source
appears to be radiating or reflecting light.

Hue

Indicates the degree to which a stimulus can be described as
similar to or different from stimuli that are described as red,
green, blue, and yellow.

Saturation

Indicates the colorfulness of a color relative to its own
brightness.

Contrast

Contrast is the ratio of black and white colors in an image.

Increasing the contrast improves the image clarity and
color brightness.

Decreasing the contrast dims the entire image.

Sharpness

Sharpness reflects the image clarity and edge sharpness.

Infrared light control mode

Indicates the mode in which the infrared light is controlled.
The options are as follows:

Auto

(default): Indicates that the IPC automatically

enables or disables the infrared light and controls the
infrared light brightness.

Manual

: Indicates that users manually enable or disable

the infrared light and control the infrared light
brightness.

NOTE

You can configure the infrared light for an IPC, so the IPC can
use it to increase the infrared illumination and enhance image
quality in extremely low illumination conditions.

The infrared light is automatically disabled in color mode.

The infrared light includes three types, dipped light, second
light and high light.

Dipped light

This parameter is available only when you set

Infrared

light control mode

Manual

. To enable the dipped light,

select the check box.
You can set

Dipped light brightness

when

Dipped light

selected. A larger value indicates higher brightness.

Second light

This parameter is available only when you set

Infrared

light control mode

Manual

. To enable the dipped light,

select the check box.
You can set

Second light brightness

when

Second light

selected. A larger value indicates higher brightness.

High light

This parameter is available only when you set

Infrared

light control mode

Manual

. To enable the dipped light,

select the check box.
You can set

High light brightness

when

High light

selected. A larger value indicates higher brightness.

IPC6221-VRZ-SP
Configuration Guide

6 Setting Video Parameters

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6221-VRZ-SP































































































































Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands

Huawei IPC6221-VRZ-SP, Configuration Manual

Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands