Huawei IPC6221-VRZ-SP Configuration Manual Download Page 38

Page: 38 / 126

Setting Video Parameters

About This Chapter

This section describes how to set video parameters, such as video and audio stream
parameters.

6.1 Setting Video and Audio Stream Parameters

You can set video and audio parameters based on the site requirements.

By configuring a stream package, you can predefine several common video and audio stream
parameters for quick invoking in the future.

6.3 Setting ISP Parameters

By setting Image Signal Processing (ISP) parameters, you can adjust video images to adapt to
different surveillance scenarios.

6.4 Configuring an ISP Package

By configuring an ISP package, you can predefine several common ISP parameters for quick
invoking in the future.

6.5 Setting ROI Parameters

By setting a region of interest (ROI), you can set the ROI quality to differentiate the ROI from
other image regions. The ROI effect is prominent at a low bit rate.

6.6 Setting Privacy Mask Parameters

You can set a privacy mask area on the live video for privacy protection.

6.7 Setting Motion Detection Parameters

An alarm is generated when an object moves within the specified surveillance range of the
camera.

IPC6221-VRZ-SP
Configuration Guide

6 Setting Video Parameters

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6221-VRZ-SP































































































































Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands

Huawei IPC6221-VRZ-SP, Configuration Manual

Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands