Huawei IPC6221-VRZ-SP Configuration Manual Download Page 36

Page: 36 / 126

PTZ Control

You can manage the IPC in the PTZ control panel during video viewing.

NOTICE

The PTZ control and configuration function is available only for cameras connected to an
external PTZ.

On the menu bar, click

Preview

. The page for viewing live video is displayed. On the left of

this page, you can use the PTZ control panel to manage the camera.

Table 5-1

describes the

buttons in the PTZ control panel.

Table 5-1

Button description

Button

Function

Click to navigate the PTZ in eight directions.

Click , the camera will rotate to the home position.

Click to adjust the aperture.

Click to adjust the image definition.

Click to adjust the camera shooting range.

If you select the

Continuous

mode, you can hold down the

directional key to rotate the PTZ continuously or release the
directional key to stop PTZ rotation.
At present, the IPC supports only the

Continuous

mode.

Click to turn the light on, or click it again to turn the light off.
This function is a reserved function and is unavailable.

IPC6221-VRZ-SP
Configuration Guide

5 PTZ Control

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6221-VRZ-SP































































































































Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands

Huawei IPC6221-VRZ-SP, Configuration Manual

Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands