manualshive.com logo in svg

Huawei IPC1801-Z36, User Manual

Share
Download
Huawei IPC1801-Z36 User Manual Download Page 87

 

IPC1801-Z36&2802-Z18&5802-Z20 
User Guide 

9 Daily Maintenance 

 

Issue 12 (2014-06-12) 

Huawei Proprietary and Confidential           

Copyright © Huawei Technologies Co., Ltd. 

77 

 

9.6 Restarting a Device 

Description 

You can restart a device in situations including the following: 

 

The device parameters are set incorrectly, and the device cannot work properly. 

 

A user needs to reset device parameters and make the setting to take effect. 

 

A device needs to be restarted remotely. 

Procedure 

Step 1

 

Choose Maintenance > Device Restart. 

The 

Device Restart

 page is displayed, as shown in Figure 9-7. 

Figure 9-7

 

Device Restart page 

 

 

Step 2

 

Click 

Restart

. 

The message "Are you sure to restart" is displayed. 

Step 3

 

Click 

OK

. 

The device is restarted successfully two or three minutes later. 

 

The High Speed Dome have power off memory function, it can restore the working condition 
automatically if it runs more than 10s before power off. 

----End 

9.7 Restoring a Device to Factory Settings 

Description 

You can restore a device to factory settings in situations including the following: 

 

The device parameters are set incorrectly, and the device cannot work properly. 

 

A user needs to reset device parameters. 

 

All parameters must be restored to the factory settings. 

 

Summary of Contents for IPC1801-Z36































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands