Huawei IPC1801-Z36 User Manual Download Page 7

Page: 7 / 94

IPC1801-Z36&2802-Z18&5802-Z20
User Guide

About This Document

Issue 12 (2014-06-12)

Huawei Proprietary and Confidential

Modified description about the security features.

3.1 Preparing Installation Tools

Modified preparing installation tools.

5.4 Setting OSD Parameters

Modified description about OSD.

9.5 Resetting the System Service Password

Modified the Reset Service Password page

Chapter 11 Technical Specifications

Modified the technical specifications.

Updates in Issue 04 (2013-01-30)

This issue is the fourth official release, compared to issue 03:

Added

2.1 Product Overview

Added a diagram showing the SD card slots and reset button.

5.2 Setting Video and Audio Stream Parameters

Added description about the recommended bit rate.

Modified

3.2 Installing a PTZ Camera

Modified the installation procedure.

9.7 Restoring a Device to Factory Settings

Modified the procedure for restoring to the factory defaults.

Deleted

Chapter 11 Technical Specifications

Deleted the stream range.

Updates in

Issue 03 (

2012-12-30

)

This issue is the third official release, compared to issue 02:

Added

Chapter 1 Security Precautions

Added description about lightening protection measures and working high above the ground.

2.2 Features

Added description about the security features.

6.3.2 Setting Security Authentication

Added description about security authentication.

Summary of Contents for IPC1801-Z36































































































Search results

Summary of Contents for IPC1801-Z36

Reviews:

Brands by name

Popular brands

Huawei IPC1801-Z36, User Manual

Search results

Summary of Contents for IPC1801-Z36

Reviews:

Brands by name

Popular brands