Huawei FusionModule 1000A20 Maintenance Manual Download Page 77

Page: 77 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Preparations

Tools: protective gloves, step ladder

Materials: spare extinguishant control panel batteries

Document: fire extinguishing device layout diagram (CE)

Skill requirement: fire engineer

Procedure

Step 1

Remove the battery cables from the extinguishant control panel.

Step 2

Remove the extinguishant control panel batteries.

Step 3

Install the spare batteries to the proper position of the extinguishant control panel.

Step 4

Connect battery cables to the extinguishant control panel in the same way.

Figure 4-36

Connecting battery cables

Distinguish the positive and negative battery terminals when connecting battery cables.

----End

4.4.9 Replacing a Fire Cylinder (CE)

Prerequisites

A spare fire cylinder of the same model is available and functional.

Impact on the System

The fire extinguishing system stops working during the replacement.

Preparations

Tools: pipe wrench, pallet truck, Phillips screwdriver, adjustable wrench, protective gloves

Materials: spare fire cylinder, sealing tape

Summary of Contents for FusionModule 1000A20























































































Search results

Summary of Contents for FusionModule 1000A20

Reviews:

Huawei FusionModule 1000A20, Maintenance Manual, Page: 77 / 86

Search results

Summary of Contents for FusionModule 1000A20

Reviews: