manualshive.com logo in svg

Huawei FusionModule 1000A20, Maintenance Manual, Page: 46 / 86

Share
Download
Huawei FusionModule 1000A20 Maintenance Manual Download Page 46

FusionModule1000A20 Prefabricated All-in-One Data 
Center 
Maintenance Guide 

4 Parts Replacement 

 

Issue 01 (2019-07-15) 

Copyright © Huawei Technologies Co., Ltd. 

39 

 

 

If a light does not work but the cables to the light are intact, the light has failed and needs 
to be replaced. 

 

If all lights after a light do not work, the light adjacent to the working light has failed.  

Step 2

 

Disconnect the power supply to the lights. 

Step 3

 

Remove the faulty light. 

 

 

During replacement, do not touch any end of the light with bare hands. You will get an 
electric shock if you touch bare electrodes. 

Step 4

 

Install the new light in the original position. 

----End 

4.2 Replacing Cooling System Components 

4.2.1 Replacing the Fresh Air Integrated Unit 

4.2.1.1 Replacing the Air Filter 

Remove the up and down covers. Loosen the two screws of fixing the air filter support, and 
remove the air filter support. Take the air filter out of the cooling product and clean it, as 
shown by the following figure. 

Figure 4-8

 

Replacing the Air Filter 

 

(1) Air filter support 

(2) Up and down outer covers 

(3) Exhaust air filter 

(4) Fresh air filter 

 

4.2.1.2 Replacing the Internal Cycle Fan 

Step 1

 

Remove the front maintenance plate and the connecting terminal of internal cycle fan. 

Step 2

 

Remove the mounting holder of internal cycle fan.  

Summary of Contents for FusionModule 1000A20























































































Reviews:

No comments