Huawei FusionModule 1000A20 Maintenance Manual Download Page 52

Page: 52 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Figure 4-14

Replacing a PSU

----End

4.3.3 Replacing a Smart ETH Gateway

Prerequisites

A spare ETH gateway of the same model is available and functional.

Impact on the System

Devices connected to the ETH gateway will be disconnected.

Preparations

Tools: ESD wrist strap, ESD gloves, Phillips screwdriver, step ladder, label, marker

Materials: spare ETH gateway

Skill requirement: extra low voltage (ELV) engineer

Procedure

Step 1

Label each cable based on the corresponding ports on the smart ETH gateway.

Step 2

Disconnect cables from the smart ETH gateway.

Step 3

Remove the faulty smart ETH gateway from the guide rails of the cable trough.

Step 4

Install the spare smart ETH gateway in the original position and connect the cables.

----End

4.3.4 Replacing an ETH Converter

Prerequisites

A spare ETH converter of the same model is available and functional.

Summary of Contents for FusionModule 1000A20























































































Search results

Summary of Contents for FusionModule 1000A20

Reviews:

Huawei FusionModule 1000A20, Maintenance Manual, Page: 52 / 86

Search results

Summary of Contents for FusionModule 1000A20

Reviews: