manualshive.com logo in svg

Huawei FusionModule 1000A20, Maintenance Manual, Page: 32 / 86

Share
Download
Huawei FusionModule 1000A20 Maintenance Manual Download Page 32

FusionModule1000A20 Prefabricated All-in-One Data 
Center 
Maintenance Guide 

3 Routine Maintenance 

 

Issue 01 (2019-07-15) 

Copyright © Huawei Technologies Co., Ltd. 

25 

 

Device 

Operation 

Check Standard 

Maintenance Guide 

by flipping it leftward. 

Warning sign 

Pull up the reset button 
on the pneumatic 
switch. 

The warning sign indicator 
is on. 

Replace the warning sign. 

Heat detector 

Heat the heat detector 
using a heating device. 

The temperature alarm 
threshold is 50°C to 65°C. 

1.

 

If the temperature is 
below the alarm 
threshold, the alarm 
indicator blinks once 
every 6s. 

2.

 

If the temperature is 
above the alarm 
threshold, the indicator 
turns on. The 
extinguishant control 
panel generates an 
alarm and triggers the 
fire alarm bell. 

Replace the heat detector. 

Smoke 
detector 

Release smoke onto the 
smoke detector using a 
smoke pistol. 

The indicator is steady on 
and the extinguishant 
control panel raises a 
corresponding alarm and 
triggers the fire alarm bell. 

Replace the smoke detector. 

Extinguishant 
abort button 

1.

 

After the manual gas 
release button is 
pressed on the 
extinguishant 
control panel, the 
gas release 
countdown starts. 
Then, press the 
extinguishant abort 
button. 

2.

 

Reset the 
extinguishant abort 
button by rotating it 
counterclockwise. 

1.

 

After the extinguishant 
abort button is pressed, 
the gas release 
countdown stops. 

2.

 

After the extinguishant 
abort button is reset, 
the gas release 
countdown starts from 
zero again. 

Replace the extinguishant abort 
button. 

Horn strobe 

Press the manual gas 
release button on the 
extinguishant control 
panel. 

The horn strobe generates 
shrill alarm sound and 
flashing signals after the 
countdown ends. 

Replace the horn strobe. 

VESDA 

Check the VESDA 
sampling pipes. 

The supports and 
connectors of the sampling 
pipes are securely 
connected. 

Replace damaged sampling pipes, 
and apply glue where pipes are not 
well sealed. 

Remove or block a 
sampling pipe. 

An alarm is generated. 

See documents delivered with the 
VESDA. 

Summary of Contents for FusionModule 1000A20























































































Reviews:

No comments