Huawei FusionModule 1000A20 Maintenance Manual Download Page 55

Page: 55 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Procedure

Step 1

Open the door of the IC card reader box.

Step 2

Remove the two screws at the bottom of the IC card reader, and remove the front cover.

Figure 4-16

Removing the front cover

Step 3

Remove the two screws that secure the IC card reader body.

Figure 4-17

Removing screws

Step 4

Remove interconnection terminals from the IC card reader, and remove the IC card reader
body.

Step 5

Remove the two screws from the bottom of the new IC card reader, and remove the front
cover.

Step 6

Reconnect the interconnection terminals, and close the door of the IC card reader box.

Step 7

Check that the new IC card reader is working properly.

The IC card reader is working properly if the pre-fab. module door can be opened from outside the
pre-fab. module using an access card and door opening operations are logged in the monitoring system.

Summary of Contents for FusionModule 1000A20























































































Search results

Summary of Contents for FusionModule 1000A20

Reviews:

Huawei FusionModule 1000A20, Maintenance Manual, Page: 55 / 86

Search results

Summary of Contents for FusionModule 1000A20

Reviews: