Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 13

Page: 13 / 112

2.1 Preparing for Installation

This section describes safety precautions and tool preparations for AP installation.

Safety Precautions

Take proper measures to prevent injuries and device damage.

Place the device in a dry and flat position away from any liquid and prevent the device
from slipping.

Keep the device clean.

Do not put the device and tools in the aisles.

CAUTION

Only the qualified personnel are permitted to install and remove the device and its
accessories. Before installation and operation, read the safety precautions carefully.

Tool Preparation

To install APs, prepare tools listed in

Table 2-1

Tools

Phillips screwdriver

Protective gloves

ESD gloves

Slip-proof glove

Marker

Hammer drill

Claw hammer

Diagonal pliers

Wire stripper

R250D
Hardware Installation and Maintenance Guide

2 AP Installation

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Summary of Contents for 50082920

















































































































Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands

Huawei 50082920, Hardware Installation And Maintenance Manual

Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands