Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 9

Page: 9 / 112

Figure 1-2

Indicator

GE1

Indicator

NOTE

The indicator is located inside the panel, which turns on after the AP is powered on.

Indicator colors may vary slightly at different temperature.

Table 1-2

Indicator description

Type

Color

Status

Description

Default status after
power-on

Green

Steady on

The AP is just
powered on and the
software is not
started yet.

Software startup
status

Green

Steady on after
blinking once

After the system is
reset and starts
uploading the
software, the
indicator blinks
green once. Until the
software is uploaded
and started, the
indicator remains
steady green.

Running status

Green

Blinking once every
2s (0.5 Hz)

The system is
running properly, the
Ethernet connection
is normal, and STAs
are associated with
the AP.

R250D
Hardware Installation and Maintenance Guide

1 Product Overview

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Summary of Contents for 50082920

















































































































Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands

Huawei 50082920, Hardware Installation And Maintenance Manual

Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands