Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 110 | Manualshive

Page: 110 / 112

background image

Com
pone
nt

No.

Applic
able
Scope

Check Item

Anten

na

1

General

The installation positions of antennas should comply with the
engineering design and antennas should be securely and
reliably installed.

2

General

There should be no obstacles in the major coverage direction
of antennas. The direction and downlink tilt of antennas
should be adjusted based on the coverage targets.

3

General

There should not be metal subjects within 1 m around an
outdoor omnidirectional antenna.

4

General

The azimuth deviation of a directional antenna should be
within 5 degrees and the tilt deviation within 0.5 degree.

5

Outdoor

antenna

The antennas are fixed using special support that supports
installation of surge protection devices and shall be located
within a 45 degree protection angle of a lightning rod. When
an antenna is mounted to a pole, the distance between the
antenna and top of the pole should be at least 30 cm.

6

Outdoor

antenna

Take waterproof measures on connectors of the antennas and
feeder cables and keep the drain holes of antennas
downwards.

7

Outdoor

antenna

The pole used in antenna mounting should meet the
following requirements:
Pole height: ≥ 2000 mm
Bottom pole diameter: ≥ 220 mm
Top pole diameter: ≥ 120 mm
Pole thickness: ≥ 6 mm
Depth of foundation: ≥ 1500 mm
The pole deployed outdoors must be reinforced with hot-dip
zinc to prevent water corrosion and rust.

8

Outdoor

antenna

It is recommended that at most three APs or antennas be
mounted to the same pole. The APs or antennas mounted to
the same pole should meet the following requirements:

l

The vertical distance should be at least 3.5 m between
adjacent 2.4G antennas and 2 m between adjacent 5G
antennas.

l

There should be at least 1 m vertical distance between
antennas that work on the same frequency band and
belong to different APs.

9

Outdoor

antenna

When outdoor APs use single-polarized antennas, the
horizontal distance between 2.4G antennas should be at least
1 m and that between 5G antennas should be at least 0.5 m.

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

104

«
...
108
109
110
111
112
»

Summary of Contents for 50082920

















































































































Reviews:

No comments

Related manuals for 50082920

Brand: Magellan Pages: 24

Brand: Ublox Pages: 44

Brand: Ubiquiti Pages: 32

Brand: Telit Wireless Solutions Pages: 48

Brand: ALCON Pages: 46

Brand: Ubiquiti Pages: 24

Brand: Advantek Networks Pages: 62

Brand: 4next Pages: 2

Brand: Ericsson Pages: 12

Brand: Digisol Pages: 86

Brand: Colubris Networks Pages: 3

Brand: Luxul Pages: 8

Brand: Doiting Pages: 19

Brand: Viega Pages: 2

Ibex-RT-610 Series

Brand: Westermo Pages: 30

VigorAccess-A48M-2-SFP-A-1-AC

Brand: Draytek Pages: 63

Brand: AAxeon Pages: 14

Brand: Ebyte Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands