HRS AQUASAVE A6 Series Operating Instructions Manual Download Page 9

Page: 9 / 58

01923 232335

www.hrshevac.co.uk

9 of 58

HRS Hevac Ltd AquaSave A6 Range

Installation, Operating & Instruction Manual

Installation

3.1

Siting

The AquaSave hot water heater shall be installed in a dry place where room temperature is below 40°C,
and ideally in ventilated premises.
AquaSave is placed preferably on a sub-base footing.

3.2

Hydraulic connections

Connect the charging kit (exc control valve + charging pump) to the storage tank using the interlink kit.

Make arrangements for fitting the insulation onto the tank before connecting up the piping.

The indirect AquaSave module can run without a recirculation system fitted.

To avoid creating a galvanic coupling, check that the materials used in the installation have similar corrosion
potentials.

3.3

Basic assembly instrustions

Assembly: refer to the full instructions given in

17 Assembly of the charging kit to the AquaSTOR.

Connect the primary supply and return connections.
Connect the cold water supply, hot water outlet and the recirculation system to the tank.

Fit the tank with a safety valve, a drain valve in the top section and a draw-off in the bottom section.

NOTE:

The valve is a compulsory fixture that has to be pre-loaded at the storage tank operating pressure.

NOTE:

The safety valve on the charging kit only protects the secondary system – it will neither protect nor

surge-feed the installation and the volume stored, in correspondence with local rules.

The safety valve shall have the same diameter as the cold water inlet fixture

Top section connection

Exchanger s accessories

Summary of Contents for AQUASAVE A6 Series



























































Search results

Summary of Contents for AQUASAVE A6 Series

Reviews:

Related manuals for AQUASAVE A6 Series

Brands by name

Popular brands

HRS AQUASAVE A6 Series, Operating Instructions Manual

Search results

Summary of Contents for AQUASAVE A6 Series

Reviews:

Related manuals for AQUASAVE A6 Series

Brands by name

Popular brands