HPE 3PAR StoreServ Page 123 Service And Upgrade Manual Download

Page: 123 / 174

Table 33: 764W PCM LEDs, alternating-current, controller node enclosure rear

view

LED

Function

Status

State

AC input fail

Amber solid

No AC power or PCM fault

Amber flashing

• Firmware Download

• Locate active

PCM OK

Green solid

AC present and PCM On / OK

Green flashing

Standby mode

Fan fail

Amber solid

PCM fail or PCM fault

Amber flashing

Firmware download

DC output fail

Amber solid

• No AC power

• Fault

• Out of tolerance

Amber flashing

Firmware download

Battery fail

Amber solid

Hard fault (not recoverable)

Amber flashing

Soft fault (recoverable)

Battery good

Green solid

Present and charged

Green flashing

Charging or disarmed

Power cooling module LEDs, alternating-current, drive enclosure

This information applies only to the HPE 3PAR 580W power cooling module for the HPE 3PAR StoreServ
8000 Storage system.

NOTE:

Labels on the PCM for the drive enclosure show the model as 580W PCM Gold Series.

Figure 106: 580W PCM LEDs, alternating-current, drive enclosure rear view

More information

123

Summary of Contents for 3PAR StoreServ















































































































































































Search results

Summary of Contents for 3PAR StoreServ

Reviews:

Related manuals for 3PAR StoreServ

Brands by name

Popular brands

HPE 3PAR StoreServ, Service And Upgrade Manual

Search results

Summary of Contents for 3PAR StoreServ

Reviews:

Related manuals for 3PAR StoreServ

Brands by name

Popular brands