HPE 3PAR StoreServ Page 115 Service And Upgrade Manual Download

Page: 115 / 174

Figure 93: Ethernet onboard ports, controller node enclosure rear view

Figure 94: Ethernet onboard ports LEDs, controller node enclosure rear view

Table 25: Ethernet onboard ports LEDs, controller node enclosure rear view

LED function

Status

State

Link up
speed

Green solid

1 Gb Link

Amber solid

100 Mb Link

Off

No link established or 10 Mb Link

Activity

Green solid

No link activity

Green flashing

Link activity

Off

No link established

FC onboard ports LEDs, controller node enclosure rear view

The controller node has two Fibre Channel (FC) onboard ports and each port includes two LEDs. The
arrow head-shaped LEDs point to the port they are associated with.

NOTE:

Incorrectly configured cables result in illuminated amber LEDs on the ports.

More information

115

Summary of Contents for 3PAR StoreServ















































































































































































Search results

Summary of Contents for 3PAR StoreServ

Reviews:

Related manuals for 3PAR StoreServ

Brands by name

Popular brands

HPE 3PAR StoreServ, Service And Upgrade Manual

Search results

Summary of Contents for 3PAR StoreServ

Reviews:

Related manuals for 3PAR StoreServ

Brands by name

Popular brands