HP Vectra VL400 Frequently Asked Questions Manual Download

Page: 64 / 74

Solving Problems 64 of 74

HP Web Services

Your Vectra

Setting Up

Using

Warranty and

Support Service

Installing

Components

Solving

Problems

CMOS Test Error

2 of 2

Advanced Troubleshooting

Have you checked that...

How

Power is correctly connected to the
system board

1 Disconnect the power cord.
2 Remove the PC’s cover.
3 Check the power connector is correctly attached to the system

board (

refer to page 73

4 Close the PC, reconnect the power cord and check that the PC

boots (starts).

You don’t need to restore the default
configuration settings

1 Switch the PC OFF then ON.
2 When the message

Press F2 to Enter Setup

appears, press the

key.

3 Press

to restore default values.

4 Press

F10

to exit the Setup program saving changes.

If the problem persists, contact your authorized support provider

Summary of Contents for Vectra VL400











































































Search results

Summary of Contents for Vectra VL400

Reviews:

Related manuals for Vectra VL400

Brands by name

Popular brands

HP Vectra VL400, Frequently Asked Questions Manual

Search results

Summary of Contents for Vectra VL400

Reviews:

Related manuals for Vectra VL400

Brands by name

Popular brands