HP Vectra VL400 Frequently Asked Questions Manual Download

Page: 27 / 74

Solving Problems 27 of 74

HP Web Services

Your Vectra

Setting Up

Using

Warranty and

Support Service

Installing

Components

Solving

Problems

The PC is Stuck in Sleep Mode

1 of 1

Have you checked that...

How

The PC is really stuck

1 Move the mouse and press any key on the keyboard. Wait a

minute to see if the PC wakes.

2 If the power LED is blinking and the PC is not making any noise,

the PC is in a deep sleep state for power saving. Press the power
button briefly and wait for a minute to see if the PC wakes up.

3 Press the power button for 5 seconds. The PC will shut down.

Any unsaved data will be lost. Press the power button briefly to
start the PC.

4 Unplug the power cord from your PC, wait for a few seconds and

then plug it in again. Your PC may restart automatically.

Summary of Contents for Vectra VL400











































































Search results

Summary of Contents for Vectra VL400

Reviews:

Related manuals for Vectra VL400

Brands by name

Popular brands

HP Vectra VL400, Frequently Asked Questions Manual

Search results

Summary of Contents for Vectra VL400

Reviews:

Related manuals for Vectra VL400

Brands by name

Popular brands