HP Vectra VL400 Frequently Asked Questions Manual Download

Page: 24 / 74

Solving Problems 24 of 74

HP Web Services

Your Vectra

Setting Up

Using

Warranty and

Support Service

Installing

Components

Solving

Problems

The PC Doesn’t Power On

2 of 2

Advanced Troubleshooting

Have you checked that...

How

The problem is not being caused by an
internal device

1 Disconnect the PC’s power cord.
2 Remove internal connectors from any accessory devices you

have added and disconnect any add-on accessory boards.

3 Reconnect the devices one by one, booting the PC each time to

see if it works correctly.

4 If you are still unable to localize the fault, contact your authorized

support provider.

The power supply is working properly

1 When you power on the PC, check that the light on the On/Off

button comes on and that you hear the power supply fan.

2 If nothing happens, contact your authorized support provider.

The original power supply unit may have to be replaced.

If the problem persists, contact your authorized support provider

Summary of Contents for Vectra VL400











































































Search results

Summary of Contents for Vectra VL400

Reviews:

Related manuals for Vectra VL400

Brands by name

Popular brands

HP Vectra VL400, Frequently Asked Questions Manual

Search results

Summary of Contents for Vectra VL400

Reviews:

Related manuals for Vectra VL400

Brands by name

Popular brands