manualshive.com logo in svg

HP Vectra VL400, Frequently Asked Questions Manual, Page: 57 / 74

Share
Download
HP Vectra VL400 Frequently Asked Questions Manual Download Page 57

Solving Problems 57 of 74

HP Web Services

Your Vectra

Setting Up

Using 

Warranty and 

Support Service 

Installing 

Components

Solving 

Problems 

Memory Test Error

1 of 1

Note: this error is indicated by a series of beeps while the screen remains blank

Have you checked that...

How

The PC’s memory modules are installed
correctly

!

1 Disconnect the power cord.
2 Remove the PC’s cover.
3 Check the memory modules are correctly installed, of the correct

type and in the correct sockets.

4 Close the PC, reconnect the power cord and check that the PC

boots (starts).

The PC’s memory modules are working

!

1 Disconnect the power cord.
2 Remove the PC’s cover.
3 Replace the memory modules by known working memory

modules from the same model of PC.

4 Close the PC, reconnect the power cord and check that the PC

boots (starts).

Advanced Troubleshooting

Have you checked that...

How

You are using the latest BIOS for your
PC

!

Download the latest BIOS and instructions for its installation from
HP’s support web site.

If the problem persists, contact your authorized support provider

Summary of Contents for Vectra VL400











































































Reviews:

No comments