manualshive.com logo in svg

HP P9000, Software Installation Manual

Share
Download
HP P9000 Software Installation Manual Download Page 48

If you change the dataset name when backing up the configuration files, make sure that you change
the prefix only.

The configuration files contain the copy group ID, DAD ID, route list ID, and path set ID. Therefore,
if you change the dataset name, the consistency between the files is lost, and then Business Continuity
Manager might become inoperable.

For details about configuration files, see the HP StorageWorks P9000 for Business Continuity
Manager Software Reference Guide.

Backing Up the Program Before Migration

Before migration, acquire a backup of the dataset where Business Continuity Manager will be
installed.

Pre-Upgrade Procedure

Deleting the User SVC

If you upgrade Business Continuity Manager versions earlier than 5.1 to Business Continuity
Manager 5.1 or later, you must delete the user SVC before you install the new version of Business
Continuity Manager.

If the user SVC was registered by using the

YKALCSVC

command, you can use the

YKALCSVC

command to delete the user SVC.

If the user SVC was registered by using the

IEASVC

xx parmlib member, you cannot use the

YKALCSVC

command to delete the user SVC. In this case, perform the procedure below.

To delete a user SVC that was registered by using the

IEASVC

xx parmlib member:

1.

Disable (comment out) the

SYMDEF

statement containing the

&YKSVCNO

system symbol in the

IEASYM

xx parmlib member.

/* SYMDEF(&YKSVCNO='SVC-number') */

2.

Disable (comment out) the

SVCPARM

statement containing the

JYUASVC

module in the

IEASYM

xx parmlib member.

/* SVCPARM   SVC-number,REPLACE,TYPE(3),EPNAME(JYUASVC) */

3.

Perform re-IPL with the

CLPA

parameter specified.

For details on steps 1 and 2, see the MVS Initialization and Tuning Reference.

Removing the Concatenation of the Cataloged Procedures Library

Remove the dataset concatenation of the following library:

Library Name

DD Name

Cataloged procedures library HPQYPRCT

IEFPDSI

If you copied the HPQYPRCT library members to a user PROCLIB, delete the copied members.

Removing the Concatenation of the REXX Exec Library and the Libraries Used by ISPF Interface

Remove the dataset concatenation of the following libraries:

Library Name

DD Name

REXX Exec library

SYSEXEC

Panel library HPQYPNLT

ISPPLIB

48

Installing Business Continuity Manager

Summary of Contents for P9000

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands