manualshive.com logo in svg

HP J2600A, Installation And Reference Manual

Share
Download
HP J2600A Installation And Reference Manual Download Page 67

HP Dial-a-LAN Remote Access
Server

The two HP AdvanceStack Dial-A-LAN auxiliary modules are remote
access servers for Ethernet networks. These products serve remote PCs,
Macintoshes, and UNIX workstations by allowing users to dial in to a 12,
24, or 48-port AdvanceStack hub.

The two models are: 

a two-port version: HP J2623A AdvanceStack Dial-A-LAN 2A/Plus
V.34

a four-port version: HP J2624A AdvanceStack Dial-A-LAN 4A

Each module requires an Ethernet SNMP Module (J2603B) for
installation into the Expansion Slot of an HP AdvanceStack hub.

If you do not have a J2603B SNMP Module already, you can purchase the
Dial-A-LAN and SNMP modules together in either of the following
bundles:

HP J2633A Dial-A-LAN 2A/Plus V.34 and HP Ethernet SNMP Module

HP J2634A Dial-A-LAN 4A with the HP Ethernet SNMP Module

HP J2623A Dial-A-LAN 2A/Plus V.34 

The HP Dial-A-LAN 2A/Plus has two RJ-11 connectors and two built-in
V.34 modems. The V.34 modems support V.34, V.FC, V.32bis, V.32, V.22,
V.22bis, V.22A/B, V.23, V.21, Bell 212A, and Bell 103. They also support
compression and error correction as specified V.42, V.42bis, MNP 2-5,
and LAP-M.

Hub Re

fe

re
nce

Hub Reference

3-17

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for J2600A











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands