manualshive.com logo in svg

HP J2600A, Installation And Reference Manual

Share
Download
HP J2600A Installation And Reference Manual Download Page 31

ThinLAN Connections

To connect a ThinLAN cable to the hub’s ThinLAN port:

1. Attach a ThinLAN cable section to one side of a BNC “T” connector.

(Hewlett-Packard offers BNC “T” connectors with insulating covers.
Order product number HP 92227A.)

2. Attach another ThinLAN cable section 

or

 a 50-ohm terminator to the

other side of the “T” connector.

3. Attach the “T” connector to the ThinLAN port.

       

4. Cover the BNC connector with an insulating cover.

To remove a ThinLAN cable, reverse this process.

N o t e

Each ThinLAN cable segment must be terminated using a 50-ohm termi-
nator at each end. In the illustration above, a 50-ohm terminator would
be placed on one side of the BNC “T” connector if that connector is at
the end of the cable segment.

BNC “T”

connector

ThinLAN cable

ThinLAN cable

50-ohm

terminator

OR

Installing the

H

P

 Advance

Stac

k Hu

bs

Installing the HP AdvanceStack 10Base-T Hubs

1-17

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for J2600A











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands