manualshive.com logo in svg

HP J2600A, Installation And Reference Manual

Share
Download
HP J2600A Installation And Reference Manual Download Page 49

Authorized Managers

The Authorized Managers window is used to specify the IP or IPX
network addresses of SNMP management stations authorized to manage
this hub and which of the stations should receive SNMP event alarms.

Backup Link

The Backup Link window is used to specify two of the hub’s network
ports (AUI, ThinLAN, or twisted-pair) to be used in a backup
(redundant) connection to another hub. It enables you to connect a
second physical link between hubs that will work if the first link fails.
The backup link is used only in the event of primary link failure, thus
eliminating the possibility of loops in the network.

See appendix D, “Backup Links” for more information.

Robust Port Control

The Robust Port Control window allows you to invoke options to
improve the hub’s ability to tolerate network problems resulting from
excessive collisions. The configurable options are:

Intelligent Segmentation Recovery

Late Collision Monitoring

These features are described in chapter 3, “Hub Reference”, under
“Auto-Segmentation”.  See the HP Stack Manager online help for
information on how to invoke these features, and when it is appropriate
to do so.

I

n

stalling an

d Using

HP Stack Manager

Installing and Using HP Stack Manager

2-11

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for J2600A











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands