manualshive.com logo in svg

HP J2600A, Installation And Reference Manual

Share
Download
HP J2600A Installation And Reference Manual Download Page 41

 Computer Requirements

The HP Stack Manager software runs on IBM-compatible personal
computers with the following minimum configuration:

Microsoft Windows version 3.1 (or later)

80386 (or higher) processor
4 Mbytes of RAM
2 Mbytes of available hard disk space
a 3-1/2" 1.44 Mbyte floppy disk drive
an available RS-232 (serial) port or modem
a VGA monitor

You will also need the following equipment to connect the PC to the hub:

a serial cable (included with hub) to connect the PC directly to the
hub, or two modems (if connecting through a modem link) and a
standard modem cable to connect the modem to the hub. The cable
included with the hub will not work as a modem cable.

See appendix A, “Cables and Connectors” for details on appropriate
cables. Connecting the hub and the PC (or modem) is described in
detail in chapter 1, “Installing the HP AdvanceStack 10Base-T Hubs”.

10Base-T twisted-pair cables (if you have multiple hubs that you are
chaining together).

I

n

stalling an

d Using

HP Stack Manager

Installing and Using HP Stack Manager

2-3

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for J2600A











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands