manualshive.com logo in svg

HP J2600A, Installation And Reference Manual

Share
Download
HP J2600A Installation And Reference Manual Download Page 58

Managing Your Hub —
HP Distributed Management

One of the key features of the HP AdvanceStack family of hubs is the
ease with which a hub can be managed. There are two main
management options:

Out-of-band management

  from a PC running HP Stack Manager

connected to the RS-232 console port of any of the hubs in the stack.

In-band management

  from a network management station running

HP Interconnect Manager anywhere on the network that the hubs
are in.

PC running HP Stack Manager

connected to the hub stack or an

ASCII terminal emulator

Network management station

on the LAN, running

HP Interconnect Manager (ICM)

HP Ethernet

SNMP Module

(required for ICM and

the ASCII terminal)

distributed management chain

Hu

b Re

fe

re

n

c

e

Hub Reference

3-8

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for J2600A











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands