manualshive.com logo in svg

HP J2600A, Installation And Reference Manual

Share
Download
HP J2600A Installation And Reference Manual Download Page 17

Power cord, one of the following:

Australia/New Zealand (8120-6175)
Denmark (8120-6178)
Europe (8120-6174)
Switzerland (8120-6179)
Japan (8120-6176)
United Kingdom (8120-6173)
United States/Canada (8120-6177)

Installation Steps

1. Install Add-in Modules (optional)

The HP AdvanceStack 10Base-T Hubs can be custom-configured by
installing an optional Ethernet SNMP Module and/or an HP Transceiver
Module. If you intend to install any of these optional modules, refer to
the documentation that was shipped with it. 

It may be more convenient to install these optional modules before
installing the hub in a rack or other location. Inspect your installation
site and identify whether the hub’s module slots will be accessible.

Installing the

H

P

 Advance

Stac

k Hu

bs

Installing the HP AdvanceStack 10Base-T Hubs

1-3

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for J2600A











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands