HP BladeSystem c3000 Troubleshooting Manual Download Page 36

Page: 36 / 108

Enclosure troubleshooting 36

Error indication

Initial step

Required steps

A server blade is powered up.
The following conditions exist:

•

The power LED is green.

•

The health LED is green.

•

The Insight Display device bay

status is blue.

No iLO 2 IP address results in
the following conditions:

•

No iLO 2 web or SSH

access

•

No enclosure DVD-ROM

drive support for this server
blade

•

No server blade information

provided to the Onboard
Administrator

•

No remote console or

remote media support

The iLO 2 on this server blade has no
IP address.

To configure the iLO 2 IP address,
reboot the server blade and use the
iLO 2 ROM setup during POST.

A server blade is powered up.

The following conditions exist:

•

The power LED is green.

•

The health LED is green.

•

The Insight Display device bay

status is red.

This issue results in the following

conditions:

•

The enclosure fan speed is

elevated to protect the server

blade.

•

The server blade cannot be

powered up if it was
manually powered down.

•

The Onboard Administrator
report of server blade

thermals and status is not
accurate.

The Onboard Administrator has lost

power and cooling communication
with iLO 2 for this server blade.
To reset iLO 2, perform one of the

following actions:

•

iLO 2.

•

Use the OA CLI command for the

bay, where N is the device bay
number.

reset server N

Because the previous action requires
restarting the server blade, always
request permission to power down the

server blade before performing this
action:
For an alternative method for resetting

iLO 2, reseat the server blade.
Reseating the server blade powers off
the server blade and iLO 2.

A server blade is powered up.

The following conditions exist:

•

The power LED is green.

•

The health LED is flashing red.

•

The Insight Display device bay

status is bright green.

—

The server blade failed to complete

POST. To troubleshoot the memory
installation, perform the following
steps:

Remove the server blade.

Verify that the memory is installed

according to the installation
guidelines provided in the server
blade documentation.

Install the server blade in the
original device bay.

Review the IML for this server
blade from OA GUI/CLI.

Review the iLO log from this server

blade for indicators.

Summary of Contents for BladeSystem c3000













































































































Search results

Summary of Contents for BladeSystem c3000

Reviews:

Related manuals for BladeSystem c3000

Brands by name

Popular brands

HP BladeSystem c3000, Troubleshooting Manual

Search results

Summary of Contents for BladeSystem c3000

Reviews:

Related manuals for BladeSystem c3000

Brands by name

Popular brands