HP AlphaServer ES47 Installation Manual Download Page 5

Page: 5 / 76

Contents

Preface

Intended Audience ................................................................................................................. ix
Document Structure ............................................................................................................... ix
Information on the Internet ..................................................................................................... x

Chapter 1 Overview

1.1

System Components .............................................................................................. 1-2

1.2

Upgrade Kit ........................................................................................................... 1-4

1.3

Upgrade Steps........................................................................................................ 1-5

Chapter 2 Prepare the System

2.1

Verify I/O Drawer Location .................................................................................. 2-2

2.2

Check Upgrade Components ................................................................................. 2-3

2.3

Check I/O Cable Length ........................................................................................ 2-4

2.4

Shut Down System Power ..................................................................................... 2-5

2.5

Remove the Side Panel .......................................................................................... 2-7

Chapter 3 Install and Cable the I/O Drawer

3.1

Install the Inner Slides ........................................................................................... 3-2

3.2

Determine Hole Locations for Installation ............................................................ 3-4

3.3

Loosely

Attach Outer Slides ............................................................................... 3-6

3.4

Attach Cable Retainer and Grommet ..................................................................... 3-8

3.5

Install the I/O Drawer .......................................................................................... 3-10

3.6

Install Cable Support Rack and Drawer Latches ................................................. 3-12

3.7

Attach Cable Guides ............................................................................................ 3-14

3.8

Attach Cable Support Bracket on Rear Door....................................................... 3-16

3.9

Identify I/O Connector on CPU Drawer .............................................................. 3-18

3.10

Connect I/O Cable(s) to CPU Drawer ................................................................. 3-20

3.11

Route the I/O Cable(s) ......................................................................................... 3-22

3.12

Connect I/O Cable(s) to I/O Drawer.................................................................... 3-24

3.13 Connect

Ethernet,

Ground, and Power Cables..................................................... 3-26

3.14 Replace

the

Side Panel......................................................................................... 3-28

Summary of Contents for AlphaServer ES47













































































Search results

Summary of Contents for AlphaServer ES47

Reviews:

Related manuals for AlphaServer ES47

Brands by name

Popular brands

HP AlphaServer ES47, Installation Manual

Search results

Summary of Contents for AlphaServer ES47

Reviews:

Related manuals for AlphaServer ES47

Brands by name

Popular brands