HP AA-RSB6B-TE Installation Manual Download Page 47

Page: 47 / 104

Installing the SAN Switch 2/8

hp StorageWorks SAN Switch 2/8 Installation Guide

Configuring SAN Switch 2/8 Network Addressing

Read the following sections for information on how to configure the SAN Switch
2/8 addressing scheme.

Requirements

The following items are required to set network addressing.

■

An IP address from your Network Administrator

■

SAN Switch 2/8 installed and connected to a power source

■

Serial cable (supplied with the switch) for connecting the switch to the
workstation

■

A local workstation (desktop or notebook computer) with:

— Microsoft

Windows 98, Windows 2000, Windows Millennium Edition,

or Windows NT 4.0 operating system

— RS-232 serial communication software (for example, ProComm Plus or

HyperTerminal)

■

Ethernet cable for connecting the switch to the workstation or to a network
containing the workstation

■

SFPs and cables, as required to connect the switch to the fabric

Setting Network Addresses via a Serial Connection

Use the following steps to verify or change the SAN Switch 2/8 IP address,
subnetmask, or gateway address.

Note:

During first time setup, you must replace the factory IP, subnetmask and gateway

addresses with addresses provided by your Network Administrator.

1. Remove the shipping plug from the SAN Switch 2/8 Serial port.

Summary of Contents for AA-RSB6B-TE









































































































Search results

Summary of Contents for AA-RSB6B-TE

Reviews:

Related manuals for AA-RSB6B-TE

Brands by name

Popular brands

HP AA-RSB6B-TE, Installation Manual

Search results

Summary of Contents for AA-RSB6B-TE

Reviews:

Related manuals for AA-RSB6B-TE

Brands by name

Popular brands