manualshive.com logo in svg

HP 9000 V2500 SCA, Operator'S Manual

The HP 9000 V2500 SCA is a high-performance device, and you can get detailed insights on its operation through the comprehensive Operator's Manual. This manual is available for free download on our website, ensuring easy accessibility for users seeking in-depth information on using this product efficiently.

Share
Download
background image

152

Chapter 7

 

Recovering from failures

Abnormal system shutdowns

/etc/rc.config.d/savecrash

) reduces system recovery time. After 

the system recovery, run 

savecrash

 manually to copy the memory 

image from the dump area to the HP-UX file system area.

Partial save

If a memory dump resides partially on dedicated dump devices and 
partially on devices that are also used for paging, only those pages that 
are endangered by paging activity can be saved. 

Pages residing on the dedicated dump devices can remain there. It is 
possible to analyze memory dumps directly from the dedicated dump 
devices using a debugger that supports this feature. If, however, there is 
a need to send the memory dump to someone else for analysis, move the 
pages on the dedicated dump devices to the HP-UX file system area. 
Then use a utility such as 

tar

 to bundle them for shipment. To do that, 

use the command 

/usr/sbin/crashutil

 instead of 

savecrash

 to 

complete the copy.

Crash information integrity

This section discusses how to make sure the part of memory that 
contains the instruction or piece of data that caused the crash is 
captured. The factors that must be considered are:

• Full dump vs. selective dump

• Dump definitions built into the kernel vs. defined at runtime

• Using a device for both paging and as a dump device

Full dump vs. selective dump

The only way to guarantee capturing the specific instruction or data that 
caused the crash is to capture everything. This means selecting a full 
dump of memory. 

Be aware, however, that this can be costly in terms of time and disk 
space. A large amount of time and disk space is needed to dump the 
entire contents of memory in a system with a large memory 
configuration or to copy a large memory image to the HP-UX file system 
area during the reboot process.

The amount of dump area should at least be equal to the amount of 
memory in the system; depending on a number of factors, additional disk 
space greater than the amount of physical memory in the system may be 
needed

Summary of Contents for 9000 V2500 SCA















































































































































































































Reviews:

No comments

Related manuals for 9000 V2500 SCA

Xerox Legacy 4127 Customer Release Notes preview
Legacy 4127
Brand: Xerox Pages: 8
ioCorp ADAPTIO 5760e User Manual preview
ADAPTIO 5760e
Brand: ioCorp Pages: 18
NEC N8100-1056F User Manual preview
N8100-1056F
Brand: NEC Pages: 408
Olive Olive 2 User Manual preview
Olive 2
Brand: Olive Pages: 44
MSI E7210 Master-FARM User Manual preview
E7210 Master-FARM
Brand: MSI Pages: 34
MAXDATA PLATINIUM 9000-4R User Manual preview
PLATINIUM 9000-4R
Brand: MAXDATA Pages: 18
Digi DIGI CONNECT ES Hardware Setup Manual preview
DIGI CONNECT ES
Brand: Digi Pages: 23
HP ProLiant BL460c Gen8 User Manual preview
ProLiant BL460c Gen8
Brand: HP Pages: 84
HP StorageWorks E Series Getting Started preview
StorageWorks E Series
Brand: HP Pages: 8
HP StorageWorks 9000s NAS Quick Reference And Rack Installation Instructions preview
StorageWorks 9000s NAS
Brand: HP Pages: 7
HP StorageWorks NAS e7000 v2 Specifications preview
StorageWorks NAS e7000 v2
Brand: HP Pages: 2
HP StorageWorks NAS e7000 v2 Quick Start Manual preview
StorageWorks NAS e7000 v2
Brand: HP Pages: 70
HP StorageWorks 600 All-in-One Maintenance And Service Manual preview
StorageWorks 600 All-in-One
Brand: HP Pages: 58
HP StorageWorks All-in-One SB600c - Storage Blade User Manual preview
StorageWorks All-in-One SB600c - Storage Blade
Brand: HP Pages: 60
7th Sense Delta User Manual preview
Delta
Brand: 7th Sense Pages: 156
QNAP TBS-464-8G Quick Installation Manual preview
TBS-464-8G
Brand: QNAP Pages: 16
Rasilient ApplianceStor 90 User Manual preview
ApplianceStor 90
Brand: Rasilient Pages: 42
Sony XDAAI1PK Brochure preview
XDAAI1PK
Brand: Sony Pages: 8

Brands by name

Popular brands

Load more brands