background image

Message

Description

Generic Drops

Number of dropped packets that are not counted by other statistics.

ESP (Rx/Tx):

Total number of ESP packets received (Rx) and transmitted (Tx) by the print server.

AH (Rx/Tx)

Total number of AH packets received (Rx) and transmitted (Tx) by the print server.

Total (Rx/Tx)

Total number of all packets received (Rx) and transmitted (Tx) by the print server.

IKE Stats

Internet key exchange (IKE) statistics for the print server are described in the following table.

Table 8-18

  IKE Statistics

Message

Description

Phase 1 Failures

Number of authentication failures that occur when the print server is establishing a
connection over IPsec. These result in connection failures.

Quick Mode Failures

Number of post-authentication failures that occur during IPsec protocol configuration,
which result in connection failures.

Rekeys

Number of times keys were regenerated. For example, this can occur after a key lifetime
setting is exceeded and then regenerated.

IKE Connections OK (1/Q)

Number of successful IPsec connections for both 

Phase 1

 and 

Quick Mode

 attempts,

separated by a slash (

Phase 1

 count / 

Quick Mode

 count).

IPsec Rules

This section of the Security page identifies the IPsec policy of the print server. The IPsec policy consists
of rules that control the security of the traffic received and transmitted by the print server. Rules are
configured using an IPsec configuration wizard, which is accessed through the print server's embedded
Web server. You can configure up to ten rules.

The heading of this section indicates the default rule for IPsec traffic (

Def

Pass

 or 

Drop

)

Pass

 Allow all non-IPsec traffic.

Drop

 Drop all non-IPsec traffic.

For each rule configured, the names of the IP address template, service template, and IPsec template
that define the rule are displayed. For more information, see 

IPsec/Firewall configuration (V.38.xx)

on page 97

.

IPsec Security Associations (SA) table

The IPsec SA Table lists the security associations of cached IPsec sessions between two hosts. For
active sessions, all detected security associations are listed in the table. If required, multiple pages
print.

Table 8-19

  IPsec Security Associations

Message

Description

SA Pair

 number

An SA table entry pair number. Up to eight entries are displayed.

Table 8-17

  IPsec statistics (continued)

ENWW

HP Jetdirect Security page 153

Summary of Contents for 630n - JetDirect Gigabit EN Print Server











































































































































































































Reviews: