manualshive.com logo in svg

HP 5500 HI Series, Configuration Manual

The HP 5500 HI Series is a premium networking solution designed to elevate your organization's connectivity. Seamlessly configure and optimize your network settings with the comprehensive Configuration Manual available for free download from our website, empowering you to unlock the full potential of this cutting-edge product.

Share
Download
background image

 

278 

the expected IPsec tunnel. If no match is found, no SA can be set up and the packets expecting to be 

protected will be dropped. 
During IKE negotiation for an IPsec policy with PFS enabled, an additional key exchange is performed. 

If the local end uses PFS, the remote end must also use PFS for negotiation and both ends must use the 

same DH group. Otherwise, the negotiation will fail. 
An SA uses the global lifetime settings when it is not configured with lifetime settings in IPsec policy view. 
When negotiating to set up SAs, IKE uses the local lifetime settings or those proposed by the peer, 

whichever are smaller. 
You cannot change the creation mode of an IPsec policy from IKE to manual, or vice versa. To create a 

manual IPsec policy, delete the IKE-mode IPsec policy, and then configure the manual IPsec policy. 

Applying an IPsec policy group to an interface 

This feature is supported only in FIPS mode. 
An IPsec policy group is a collection of IPsec policies with the same name but different sequence numbers. 
In an IPsec policy group, an IPsec policy with a smaller sequence number has a higher priority. 
You can apply an IPsec policy group to a logical or physical interface to protect certain data flows. To 

cancel the IPsec protection, remove the application of the IPsec policy group. 
For each packet to be sent out an IPsec protected interface, the system looks through the IPsec policies in 
the IPsec policy group in ascending order of sequence numbers. If an IPsec policy matches the packet, 

the system uses the IPsec policy to protect the packet. If no match is found, the system sends the packet out 

without IPsec protection. 
To apply an IPsec policy group to an interface: 

 

Step Command 

1.

 

Enter system view. 

system-view 

2.

 

Enter interface view. 

interface

 

interface-type interface-number

 

3.

 

Apply an IPsec policy group to the 
interface. 

ipsec

 

policy

 

policy-name

 

 

 

NOTE: 

•

 

IPsec policies can be applied only to VLAN interfaces and Layer 3 Ethernet interfaces on the switch. 

•

 

An interface can reference only one IPsec policy group. An IPsec policy can be applied to only one 
interface. 

 

Configuring the IPsec session idle timeout 

This feature is supported only in FIPS mode. 
An IPsec session is created when the first packet matching an IPsec policy arrives. Also created is an IPsec 

session entry, which records the quintuplet (source IP address, destination IP address, protocol number, 

source port, and destination port) and the matched IPsec tunnel. 
An IPsec session is automatically deleted after the idle timeout expires. 
Subsequent data flows search the session entries according to the quintuplet to find a matched item. If 

found, the data flows are processed according to the tunnel information; otherwise, they are processed 

Summary of Contents for 5500 HI Series





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5500 HI Series

NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Billion BiPAC 4500NZ(L) User Manual preview
BiPAC 4500NZ(L)
Brand: Billion Pages: 146
3Com EtherLink 3C509B Quick Manual preview
EtherLink 3C509B
Brand: 3Com Pages: 8
ZyXEL Communications ZyXEL EES-1024AF User Manual preview
ZyXEL EES-1024AF
Brand: ZyXEL Communications Pages: 99
VCS VideoJet 100 Manual preview
VideoJet 100
Brand: VCS Pages: 118
Maipu MP2900-04-AC Installation Manual preview
MP2900-04-AC
Brand: Maipu Pages: 80
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
Active Communications ACS express Quick Start Manual preview
ACS express
Brand: Active Communications Pages: 10
Watchguard Firebox T20 Hardware Manual preview
Firebox T20
Brand: Watchguard Pages: 21
Net Optics Phantom HD Quick Install Manual preview
Phantom HD
Brand: Net Optics Pages: 2
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Brand: Avocent Pages: 2
Cayman Systems 2E-H-W User Manual preview
2E-H-W
Brand: Cayman Systems Pages: 170
Netopia D3100-I User Reference Manual preview
D3100-I
Brand: Netopia Pages: 138
DELTA GROUP LOYTEC LIP‑3ECTC Installation Instructions preview
LOYTEC LIP‑3ECTC
Brand: DELTA GROUP Pages: 4
ZyXEL Communications Dimension GS-2024 User Manual preview
Dimension GS-2024
Brand: ZyXEL Communications Pages: 266
Airlinkplus UG-ASW232-1103 User Manual preview
UG-ASW232-1103
Brand: Airlinkplus Pages: 24
8e6 Technologies Threat Analysis Reporter TAR Quick Start Manual preview
Threat Analysis Reporter TAR
Brand: 8e6 Technologies Pages: 76
National Instruments FIELD POINT Installation Manual preview
FIELD POINT
Brand: National Instruments Pages: 4

Brands by name

Popular brands

Load more brands