manualshive.com logo in svg

HP 445860-B21 - 10Gb Ethernet BL-c Switch, Reference Manual

The HP 445860-B21 - 10Gb Ethernet BL-c Switch is a powerful networking solution for high-performance data centers. To fully utilize its features, you can easily download the Command Reference Manual from manualshive.com, free of charge. This comprehensive manual offers detailed instructions and invaluable insights to optimize your network setup.

Share
Download
background image

 

 

 

Dashboard

 

 

 

  

 

30

 

Switch Ports Dashboard 

To display the following form, select 

Switch Ports

 (click the underlined text, not the folder). 

 

The following table describes the Switch Ports Dashboard controls: 

Table 11 

 Switch Ports Dashboard controls 

 

Control Description 

Status 

Displays the port status, as follows:  

•

 

black: disabled 

•

 

green: enabled 

•

 

blue: down  

Switch Port Info 

Summarizes the following port information: 

•

 

STP:

 Shows if the port has Spanning Tree Protocol enabled or disabled. 

•

 

rmon:

 Shows if RMON is enabled or disabled.  

•

 

tagging:

 Shows if this port has VLAN Tagging enabled or disabled. 

•

 

PVID:

 VLAN ID of any VLAN(s) to which this port is a member. 

Operational Status 

Displays the operational status of the port. 

Summary of Contents for 445860-B21 - 10Gb Ethernet BL-c Switch







































































































































































































































































Reviews:

No comments

Related manuals for 445860-B21 - 10Gb Ethernet BL-c Switch

j5 create JUH450 User Manual preview
JUH450
Brand: j5 create Pages: 7
GRAS RA4800 Instruction Manual preview
RA4800
Brand: GRAS Pages: 6
NetComm NP544 Specifications preview
NP544
Brand: NetComm Pages: 2
IOGear GUF202 User Manual preview
GUF202
Brand: IOGear Pages: 28
Konix 3328170265072 User Manual preview
3328170265072
Brand: Konix Pages: 12
Cotell IH2510E-A-WM Installation Manual preview
IH2510E-A-WM
Brand: Cotell Pages: 8
Digitus DA-70148-3 User Manual preview
DA-70148-3
Brand: Digitus Pages: 10
Tripp Lite MTB3-002-DP Quick Start Manual preview
MTB3-002-DP
Brand: Tripp Lite Pages: 25
SSS Siedle ZTL 051-0 Product Information preview
ZTL 051-0
Brand: SSS Siedle Pages: 8
Eastern Times Technology GBU522 Quick Start Manual preview
GBU522
Brand: Eastern Times Technology Pages: 9
Panasonic et-adser Specifications preview
et-adser
Brand: Panasonic Pages: 1
Panasonic ET-UW100 Brochure & Specs preview
ET-UW100
Brand: Panasonic Pages: 2
Panasonic DMW-USBC1 Operating Instructions preview
DMW-USBC1
Brand: Panasonic Pages: 2
Panasonic CYZAC50N Operating Instructions preview
CYZAC50N
Brand: Panasonic Pages: 2
Panasonic DBUB-P207 User Manual preview
DBUB-P207
Brand: Panasonic Pages: 5
Panasonic DBUB-P705 User Manual preview
DBUB-P705
Brand: Panasonic Pages: 6
Panasonic CF-AA6503A2 Operating Instructions Manual preview
CF-AA6503A2
Brand: Panasonic Pages: 6
Panasonic DE-852D Operating Instructions Manual preview
DE-852D
Brand: Panasonic Pages: 8

Brands by name

Popular brands

Load more brands