manualshive.com logo in svg

HP 445860-B21 - 10Gb Ethernet BL-c Switch, Reference Manual

The HP 445860-B21 - 10Gb Ethernet BL-c Switch is a powerful networking solution for high-performance data centers. To fully utilize its features, you can easily download the Command Reference Manual from manualshive.com, free of charge. This comprehensive manual offers detailed instructions and invaluable insights to optimize your network setup.

Share
Download
background image

 

 

 

Dashboard

 

 

 

  

 

31

 

Table 11 

 Switch Ports Dashboard controls 

 

Control Description 

Speed/Duplex/Flow Ctl 

Displays parameters for the port link. 

Input Frames/Output Frames 

Displays the number of frames that have been received by this port (Input 

Frames) and the number of frames that have been transmitted by this port 
(Output Frames). 

Link State Changes/Total Errors 

Displays the total number of link state changes for this port and the total 

number of errors logged by this port. 

 

For more information, select a port number to display detailed statistics for that port. 

802.1x System Information 

To display the following form, select 

Layer 2 > 802.1x > General.

 

 

The following table describes the 802.1x  system information fields: 

Table 12 

 802.1x System information 

 

Control Description 

System Capability 

Displays the capability of the switch as an 802.1x Authenticator. It cannot be 

used as an Authentication Server or a Supplicant. 

System Status 

Displays the current state (enabled or disabled) of 802.1x access control. 

Protocol Version 

Displays the 802.1x protocol version number. 

 

Summary of Contents for 445860-B21 - 10Gb Ethernet BL-c Switch







































































































































































































































































Reviews:

No comments

Related manuals for 445860-B21 - 10Gb Ethernet BL-c Switch

TEXIO GP-600B Instruction Manual preview
GP-600B
Brand: TEXIO Pages: 49
Allied Telesis 29M2/SP-BA Installation And User Manual preview
29M2/SP-BA
Brand: Allied Telesis Pages: 90
Seagate FreeAgent DockStar Reviewer'S Manual preview
FreeAgent DockStar
Brand: Seagate Pages: 13
Linksys WUSBF54G Product Data preview
WUSBF54G
Brand: Linksys Pages: 2
Harman Kardon BTA 10 Quick Setup Manual preview
BTA 10
Brand: Harman Kardon Pages: 8
COPTONIX I2C-RS232-Adapter Manual preview
I2C-RS232-Adapter
Brand: COPTONIX Pages: 15
ZLAN ZLAN8100 User Manual preview
ZLAN8100
Brand: ZLAN Pages: 18
TERK Technologies XMDirect XMDPIO110 Installation Manual preview
XMDirect XMDPIO110
Brand: TERK Technologies Pages: 6
V7 UCWDA User Manual preview
UCWDA
Brand: V7 Pages: 23
LSILogik eXtreemeRAID 3000 Quick Installation Manual preview
eXtreemeRAID 3000
Brand: LSILogik Pages: 24
Asus USB-AC51 User Manual preview
USB-AC51
Brand: Asus Pages: 26
Asus USB-AC50 User Manual preview
USB-AC50
Brand: Asus Pages: 36
Asus USB-AC53 Quick Start Manual preview
USB-AC53
Brand: Asus Pages: 2
D-Link DWM-152 User Manual preview
DWM-152
Brand: D-Link Pages: 36
UGREEN CM493 User Manual preview
CM493
Brand: UGREEN Pages: 7
Duel Systems DL-0002 Installation Manual preview
DL-0002
Brand: Duel Systems Pages: 58
Adaptec ANA-7711C Getting Started Manual preview
ANA-7711C
Brand: Adaptec Pages: 12
Adaptec 78165 SAS/SATA RAID Datasheet preview
78165 SAS/SATA RAID
Brand: Adaptec Pages: 2

Brands by name

Popular brands

Load more brands