manualshive.com logo in svg

Hoval TopGas 80, Installation Instructions Manual, Page: 3 / 38

Share
Download
Hoval TopGas 80 Installation Instructions Manual Download Page 3

3

4 213 894 / 01 

TABLE OF CONTENTS

5. Commissioning ..................................................................................................................................... 25

5.1 

Setting the control .............................................................................................................................................................25

5.2 

Water quality ......................................................................................................................................................................25

5.2.1 

Heating water..................................................................................................................................................................25

5.2.2 

Filling and replacement water .........................................................................................................................................25

5.2.3 

Filling up the system .......................................................................................................................................................26

5.3 

Gas adjustment ..................................................................................................................................................................26

5.3.1 

Bleeding the gas pipeline ................................................................................................................................................26

5.3.2 Commissioning ...............................................................................................................................................................26

5.3.3 

Gas inlet pressure ...........................................................................................................................................................26

5.3.4 

Gas fitting .......................................................................................................................................................................26

5.3.5 

Setting the gas flow rate .................................................................................................................................................27

5.4 

Changing to a different kind of gas ..................................................................................................................................28

5.5 

Handing over to the user ...................................................................................................................................................28

5.5.1 

Instruction the user .........................................................................................................................................................28

5.5.2 

Checking the water level .................................................................................................................................................28

5.5.3 Maintenance ...................................................................................................................................................................28

6. Decommissioning ................................................................................................................................. 29

7. Maintenance .......................................................................................................................................... 30

7.1 

Checking the water connections for leakage ...................................................................................................................30

7.2 

Maintenance includes ........................................................................................................................................................30

7.3 

Cleaning the heat exchanger ............................................................................................................................................30

7.4 

Function check ..................................................................................................................................................................30

7.5 

Emission measurement .....................................................................................................................................................30

8. Faults ..................................................................................................................................................... 32

9. 

Automatic firing unit BIC 335-Parameter list ....................................................................................... 34

Summary of Contents for TopGas 80







































Reviews:

No comments