background image

4

4 205 254 / 03

Important information

Important Information

1. 

Symbols

1.1 

 

Safety information

 

(Instructions for the safety and protec-
tion of persons)

 

Warning information

 

(Instructions  for  the  protection  of  the 
heating system)

Bold type

 

= Important information

Guarantee

1.2 

Important Note
Proper  functioning  is  only  guaranteed  if  the 
operating  instructions  are  observed  and  the 
boiler is regularly maintained according to the 
DVGW (German association of gas and water 
management  /  ÖVGW  (Austrian  association 
of  gas  and  water  management),  respectively 
SVGW  (Switzerland  association  of  gas  and 
water management) directives by an approved 
specialist. Troubleshooting and damage repair 
caused by contaminated operating media (gas, 
water, combustion air), unsuitable chemical ad-
ditives to the heating water, incorrect handling, 
faulty  installation,  inadmissible  modifications 
and damage due to the exercising of force are 
not covered by our warranty; the same applies 
to corrosion through halogen compounds, e.g. 
from  spray  cans,  paints,  adhesives,  solvents 
and cleaning agents. 
Hoval gas boilers are only to be installed by ap-
proved specialists. No modifications are to be 
made to the boilers.

Other instructions

1.3 

Depending on the model, any further instructions are 
enclosed with the individually packed components.

-  Adjustment 
-  Accessories

Further information sources

-  Hoval catalogue
-  Standards, regulations

Safety instructions

1.4 

When working on the TopGas

®

 the following points 

need to be noted:

If you smell flue gas or gas:

no open fire or sparks,

 

-

do not smoke,

 

-

deflector off the heating system,

 

-

close the gas cock,

 

-

open doors and windows

 

-

 

The system may only be placed in operation when 

• 

all relevant standards and safety regulations have 
been complied with. However, for a trial operation, 
at least the following conditions must be satisfied:
-  Safety valve installed (closed system)
-  Control operative (connected to power supply) 
-  System filled with water 
-  Expansion tank connected
-  Boiler is connected to the regulation type flue gas 

pipeline

-  Burner is preset

With maintenance and repair

• 

-  Allow the gas boiler to cool.
-  Deflector off the gas boiler and disconnect from 

the electrical supply.

-  Shut off the gas cock.
-  Close  the  shut-off  cocks  of  the  appliance  (cold 

water, heating flow and return).

-  Inappropriate actions on water-carrying parts of 

the gas boiler can result in an outflow of hot water 
and cause severe burns.

-  Replace  all  removed  covers  and  cladding  on 

completion of the repair / maintenance work.

-  Do not exceed the maximum operating pressure 

and temperature of the gas boiler (see identifica-
tion plate).

-  Open  the  appliance  cocks  (cold  water,  heating 

flow and return).

-  Open the gas cock.

Summary of Contents for TopGas 30



































Reviews: