HouseWarmer HWDV081 Page 7 Installation Instructions And Owner'S Manual Download | Manualshive

Page: 7 / 48

background image

33444-0-0414

Page 7

UNIT DIMENSIONS

MAKE SURE APPLIANCE IS SUITABLE FOR THE GAS SUPPLY AVAILABLE:

NATURAL GAS

OR

PROPANE/LP.

NOTE: Dimensions Rounded To Nearest 1/16” (1.6mm)

9” (228.6mm) (HWDV081)
9-1/2” (241.3mm) (HWDV150)

21-11/16” (550.9mm) (HWDV081)
25-5/16” (642.9mm) (HWDV150)

22-5/16” (566.7mm) (HWDV081)

18-5/16” (465.1mm) (HWDV150)

«
...
5
6
7
8
9
...
»

Summary of Contents for HWDV081

















































Reviews:

No comments

Related manuals for HWDV081

EL180UHNE Series

Brand: Lennox Pages: 8

Brand: ECR International Pages: 44

Brand: Braemar Pages: 2

Brand: Braemar Pages: 15

Brand: Paragon Pages: 19

Brand: Carrier Pages: 6

Brand: Earth Pages: 57

Brand: Bard Pages: 30

Brand: United States Stove Pages: 20

Brand: ICP Pages: 26

GE NF80XV Series

Brand: Haier Pages: 48

NTG3/FBF Series

Brand: ICP Pages: 16

Brand: Valley Comfort Systems Pages: 36

Brand: York Pages: 4

Brand: EDG Pages: 30

Brand: Yamato Pages: 48

Brand: Yamato Pages: 65

Brand: Lennox Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands