background image

9.800-087.0, 8.941-124.0, 8.941-459.0   •  Rev. 10/09

OPERA

TOR’S MANU

AL

  

PRESSURE 

W

ASHER 

 

4

 

 

COMPONENT IDENTIfICATION

Spray gun — Controls the application of water and 
detergent  onto  cleaning  surface  with  trigger  device. 
Includes safety latch.
Straight Through Wand — Must be connected to the 
spray gun.
Swivel Connector - Allows free range of movement to 
avoid coiling hoses.
Note: If trigger on spray gun is released for more 
than  2  minutes,  water  will  leak  from  valve. Warm 
water will discharge from pump protector onto floor.  
This system prevents internal pump damage.

Detergent  Injector  -  Allows  you  to  siphon  and  mix 
detergents.
High  Pressure  Hose  —  Connect  one  end  to  water 
pump  discharge  nipple  and  the  other  end  to  spray 
gun.
Nozzle quick Coupler - 
Pump — Develops high pressure.
Starter  grip  —  Used  for  starting  the  engine  manu-
ally.

Detergent 

Hose

Unloader

Engine

Water Supply 

Hose  

(Not Included)

Wand

High Pressure Nozzle 

Soap Nozzle 

Trigger

Spray gun

High Pressure 

Hose

Inlet Water

Detergent bucket 

(Not Included)

quick 

Coupler

Inlet 

Connection

Pump

Swivel 

Connector

Summary of Contents for HC-232336

















Reviews: