Hotsy HC-232336 Operator'S Manual Download

Page: 6 / 16

9.800-087.0, 8.941-124.0, 8.941-459.0 • Rev. 10/09

PRESSURE

ASHER

OPERA

TOR’S MANU

ASSEMbLy INSTRUCTIONS

STEP 1: Attach the high pressure
hose to the spray gun using teflon
tape on hose threads.

STEP 2: Attach nozzle extension
to spray gun/wand. Tighten both
by hand.

STEP 3: Before installing nozzle,
turn on water supply and run ma-
chine allowing water to flush through
the system until clear.

Safety

Latch

Spray

gun

High Pressure

Hose

Nozzle Extension

Spray gun/

Wand

STEP 6: Connect garden hose to
the cold water source.

Cold

Water

Source

garden

Hose

STEP 7: Pull the spring-loaded collar of the wand
coupler back to insert your choice of pressure nozzle.
Release the coupler collar and push the nozzle until the
collar clicks. Pull the nozzle to make sure it is seated
properly.

Pressure

Nozzle

Wand

Coupler

Collar

STEP 4: Connect the high pres-
sure hose to the pump discharge
fitting. Push coupler collar forward
until secure.

Pump

Discharge

fitting

High

Pressure

Hose

Coupler Collar

STEP 5: Connect the garden hose
to pump water inlet. Inspect inlets.

CAUTION: Do not run the pump
without water or pump damage
will result.

Pump

Water Inlet

garden

Hose

Summary of Contents for HC-232336

















Search results

Summary of Contents for HC-232336

Reviews:

Related manuals for HC-232336

Brands by name

Popular brands

Hotsy HC-232336, Operator'S Manual

Search results

Summary of Contents for HC-232336

Reviews:

Related manuals for HC-232336

Brands by name

Popular brands