background image

Hotsy EP  •  8.914-444.0  •  Rev. 07/13

OPERA

T

OR’S MANU

AL

  

PRESSURE W

ASHER

  

4

INTRODUCTION & IMPORTANT SAFETY INFORMATION

Thank you for purchasing this Pressure Washer.

We reserve the right to make changes at any time 
without incurring any obligation.

Owner/User Responsibility:

The owner and/or user must have an understanding of 
the manufacturer’s operating instructions and warnings 
before using this pressure washer. Warning information 
should be emphasized and understood. If the operator 
is not fl uent in English, the manufacturer’s instructions 
and warnings shall be read to and discussed with 
the operator in the operator’s native language by the 
purchaser/owner, making sure that the operator com-
prehends its contents.

Owner and/or user must study and maintain for future 
reference the manufacturers’ instructions.

The operator must know how to stop the machine 
quickly and understand the operation of all controls. 
Never permit anyone to operate the engine without 
proper instructions.

SAVE THESE  INSTRUCTIONS 

This manual should be considered a permanent 
part of the machine and should remain with it if 
machine is resold.

When ordering parts, please specify model and 
serial number. Use only identical replacement parts.

This machine is to be used only by trained operators.

IMPORTANT SAFETY 

INFORMATION

READ OPERATOR’S 

MANUAL THOROUGHLY 

PRIOR TO  USE.

WARNING: To reduce the risk of 

injury, read operating instruc-
tions carefully before using.

  1.  Read the owner's manual 

thoroughly. Failure to follow 
instructions could cause mal-
function of the machine and 
result in death, serious bodily 
injury and/or property damage.

 

2. 

Know how to stop the 

machine and bleed pressure quickly. Be thoroughly 
familiar with the controls.

  3.  Stay alert — watch what you are doing.

  4. All installations must comply with local codes. 

Contact your electrician, plumber, utility company 
or the selling distributor for specifi c details. If your 
machine is rated 250 volts or less, single phase will 
be provided with a ground fault circuit interrupter 
(GFCI). If rated more than 250 volts, or more than 
single phase this product should only be connected 
to a power supply receptacle protected by a GFCI.

DANGER: Improper connection of the equipment-
grounding conductor can result in a risk of elec-
trocution. Check with a qualified electrician or 
service personnel if you are in doubt as to whether 
the outlet is properly grounded. Do not modify the 
plug provided with the product - if it will not fi t the 
outlet, have a proper outlet installed by a qualifi ed 
electrician. Do not use any type of adaptor with 
this product

WARNING

KEEP WATER

SPRAY AWAY FROM 

ELECTRICAL WIRING.

WARNING: Keep wand, hose, and 

water spray away from electric 
wiring or fatal electric shock may 
result.

5. 

To protect the operator from  

 

electrical shock, the machine  

 

must be electrically grounded. 

 

It is the responsibility of the  

 

owner to connect this machine 

to a UL grounded receptacle of proper voltage and 
amperage ratings. Do not spray water on or near 
electrical components. Do not touch machine with 
wet hands or while standing in water. Always dis-
connect power before servicing.

RISK OF EXPLOSION: 

DO NOT SPRAY 

FLAMMABLE LIQ-

UIDS.

WARNING

WARNING: Flammable liquids 

can create fumes which can ig-
nite, causing property damage 
or severe injury.

WARNING: Risk of explosion — 
Do not spray fl ammable liquids.

 
 

6. 

Do not allow acids, 

caustic or abrasive fl uids to pass through the pump.

  7. Never run pump dry or leave spray gun closed 

longer than 1-2 minutes.

  8.  Keep operating area clear of all persons.

WARNING

USE PROTECTIVE 

EYE WEAR

AND CLOTHING 

WHEN OPERATING

THIS EQUIPMENT.

WARNING: High pressure spray 

can cause paint chips or other 
particles to become airborne 
and fl y at high speeds. To avoid 
personal injury, eye, hand and 
foot safety devices must be 
worn.

  9.  Eye, hand, and foot pro-

tection must be worn when 
u s i n g   t h i s   e q u i p m e n t .

Summary of Contents for EP-2010
























Reviews: