manualshive.com logo in svg

Hotpoint 96797, Service Information, Page: 29 / 43

Share
Download
Hotpoint 96797 Service Information Download Page 29

29 of 43

Whirlpool UK Appliances Ltd

Service Manual UK

English

CONFIGURATION & TEST MODE

IMPORTANT NOTE:

 There is a wireless communication port which is located in the upper / right part of 

the product as shown and is used to programme the main board during the manufacturing process.

BE CAREFUL: CONFIGURE THE OVEN WITH THE TOP COVER IN PLACE OTHERWISE YOU 
WILL RECEIVE AN F04 ERROR AND IN ADDITION IT WILL BE NOT POSSIBLE TO 
REPROGRAMME THE MAIN BOARD BECAUSE OF THE LIGHT AFFECTS ON THE OPTICAL 
SENSOR INSIDE THE MAIN BOARD.

1.

Disconnect the oven from the electrical supply and wait approximately 10 seconds.

2.

Reconnect to the electrical supply.

3.

Press the touch control OK button and hold for 5 seconds. A confirmation beep will sound. Release 
the button.

4.

Press the OK button 4 times within 5 seconds. The 'Manual Test' procedure will be entered.

5.

CONF will be displayed.

6.

Press the OK button again for at least 1 second.

7.

The following images show the sequence of the configuration and the test programme.

8.

Set the configuration number for the User Interface (UI) by turning the central knob. Refer to the 
Configuration Code in Specifications or on the Rating Plate of the oven for the correct code.
For confirmation and advancing onto the next step always press the Start button 

.

CONF

UI00

Summary of Contents for 96797












































Reviews:

No comments